Search found 1333 matches
- Tue Mar 05, 2024 4:51 pm
- Forum: The Off-Topic Section
- Topic: Today I Received...
- Replies: 649
- Views: 310973
Re: Today I Received...
I rescued a BBC Basic manual from a school I worked out - was for RM machines - but it contains the full list of commands. Also since picked up some books on the Z88 that cover BBC Basic - It's a good version of the language.
- Fri Mar 01, 2024 4:27 pm
- Forum: Hardware
- Topic: Thor 8 with no keyboard
- Replies: 7
- Views: 1626
Re: Thor 8 with no keyboard
I watched those as well, wonder who got them?
- Mon Feb 26, 2024 9:50 am
- Forum: Hardware
- Topic: Switching Regulator?
- Replies: 37
- Views: 5324
- Mon Feb 26, 2024 8:19 am
- Forum: Hardware
- Topic: Switching Regulator?
- Replies: 37
- Views: 5324
Re: Switching Regulator?
The only issue I could see is that some of the older switching regulator circuits operate in the lower frequencies and might produce radiated interference that could affect the microdrives, but more modern designs use very high KHz or even MHz range and so this is less likely going to be an issue. A...
- Thu Feb 22, 2024 11:56 am
- Forum: Hardware
- Topic: Floppy enclosure 3d print
- Replies: 7
- Views: 1282
Re: Floppy enclosure 3d print
That's nice
- Sat Feb 17, 2024 11:13 am
- Forum: General QL Chat
- Topic: My rare old QL version AH
- Replies: 22
- Views: 3831
Re: My rare old QL version AH
No photo's I'm afraid - but if you look at the issue 5 board - there is a wire link or zero ohm resistor that connects pin 40 to VCC - it's marked on the PCB as a diode - and that's the first clue - this is the VCC for battery - which should be a wired or'd pair of diodes - one that from VCC to pin ...
- Fri Feb 16, 2024 7:32 am
- Forum: General QL Chat
- Topic: My rare old QL version AH
- Replies: 22
- Views: 3831
Re: My rare old QL version AH
The battery area was under the heatsink and near the modulator - but I've never seen a board fitted with it. I did make this mod myself on and old QL, but it involves some tweaking with the reset signal during power up - if I did it again I'd use one of the power management chips that locks out the ...
- Thu Feb 15, 2024 3:22 pm
- Forum: Hardware
- Topic: QL PSU Voltages
- Replies: 20
- Views: 910
Re: QL PSU Voltages
That should be more than enough I would have thought
- Thu Feb 15, 2024 1:58 pm
- Forum: Hardware
- Topic: QL PSU Voltages
- Replies: 20
- Views: 910
Re: QL PSU Voltages
One thing I would say - Charlies vRetro uses some sort of stepped square wave format for the AC voltage - it works fine with the power circuity in the QL for generating +/- 12V using the small L series TO92 regulators (look like transistors), and I don't think this AC voltage is used any where else ...
- Thu Feb 15, 2024 1:54 pm
- Forum: Hardware
- Topic: QL PSU Voltages
- Replies: 20
- Views: 910
Re: QL PSU Voltages
I know that if I have too much plugged in (curse those backplanes :-) ) the vRetro will gracefully abort trying to power the QL up. but it will happily run one expansion card in the QL no problem. I can't remember what spec my little power supply is, but I think it's 12V at 2.5A - which provides mor...